International Plumbing Code Practice Test

These questions are part of the practice quiz. Start practicing

• In a parallel water distribution system, how should hot water piping be managed when bundled with cold water piping?
• What is essential for changes in diameter greater than two pipe sizes in drain pipes?
• What is the minimum uniform gauge pressure required for an air test on a drainage and vent system?
• A thermal expansion tank must be supported according to what?
• What is the purpose of a drainage system?
• What is the required diameter for the waste outlet of bathtubs?
• What feature allows the user to flush a water closet with variable water volume?
• What is the minimum square area required for all shower compartments?
• A water heater shall have a level working space not less than ____ inches in length and ____ inches in width in front of the control side.
• Which of the following describes an interceptor?
• How is thermal expansion managed in plumbing systems?
• When water pressure within a building exceeds what pressure must an approved water pressure reducing valve be installed?
• What is the minimum clearance required in front of a water closet, urinal, lavatory, or bidet?
• The maximum temperature of water from tankless water heaters intended for domestic use shall not exceed ____ ﾟF.
• What does septic tank primarily serve?
• Sinks must have waste outlets of a minimum diameter of what size?
• How often should annual inspections of backflow prevention assemblies and air gaps be conducted?
• In structures where separate toilet facilities are required for both sexes, which types of facilities may be permitted?
• How wide and deep must water closet compartments be for floor-mounted units?
• Which item is included in a typical bathroom group?
• What is the minimum dimension requirement for bidets in terms of distance from obstacles?
• What is the purpose of the clearance requirement in front of plumbing fixtures?
• Which of the following is a requirement for water service pipe used in construction?
• What is the primary function of a flush tank?
• When the manufacturer’s instructions conflict with code provisions, what should be followed?
• What type of solders and fluxes should be used for soldered joints of copper water supply piping?
• Which of the following describes a bathroom group?
• What characterizes a combination waste and vent system?
• What must water from an individual water supply be approved as before connection to the plumbing system?
• What is the minimum horizontal separation distance required between water service pipe and the building sewer?
• What is the minimum working pressure rating for water service pipe or tubing installed underground and outside of a structure?
• What is the maximum temperature that a water temperature limiting device should be adjusted to provide?
• What does the term "occupancy" refer to in plumbing terms?
• What happens when a permit is issued without proper adhering to code provisions?
• What is the primary purpose of the plumbing code?
• Which type of water is defined as having a temperature range between 85°F and 110°F?
• How much larger should sleeves be than the pipes passing through a foundational wall?
• What is the minimum size of water supply pipe for lavatories?
• What is the definition of nonpotable water?
• What is the minimum required distance from the center of a water closet to any obstruction?
• Where should potable water pumps be mounted in basements?
• Ropool bathtub pumps shall be located above the ____ of the fixture trap.
• What is the advantage of having lavatories near water closets in public facilities?
• Unless otherwise provided, plumbing fixtures must be supplied with what type of water?
• Which of the following best describes the role of traps in plumbing?
• What is a valve or faucet that closes automatically when released manually known as?
• Which equipment is specifically designed to heat and supply potable water?
• What type of valves must be installed on the water supply pipe to every water heater?
• Separate toilet facilities are not required in buildings with an occupant load of how many or fewer?
• What do indirect waste pipes typically discharge into?
• For what does the plumbing term "branch" refer?
• What is the final inspection of a building based on?
• How far must piping be installed from the nearest edge of studs, joists, or rafters to avoid damage?
• What is the minimum depth for exterior water supply piping below grade?
• What is the minimum number of fixtures required if the total occupant load is 400?
• Water heaters must be certified by which of the following?
• What is the term for the fall (pitch) of a pipe in relation to a horizontal plane?
• For what purpose is a dual flushing device primarily designed?
• What determines how many plumbing fixtures are required in a facility?
• What type of test is required for the completed drainage and vent system to ensure compliance with the code?
• In plumbing, what does the term "developed length" specifically refer to?
• What is the extension of a soil or waste stack above the highest horizontal drain connected to it called?
• What type of water closet bowls are required for public or employee toilet facilities?
• At what height should urinal partitions begin, according to plumbing standards?
• What distinguishes a full-open valve from other types of valves?
• For effective drainage, a floor drain must be connected to what?
• How does the pressure rating of 100 PSI for hot water distribution pipes ensure safety?
• What is the purpose of a waste receptor in plumbing systems?
• Food waste disposers must have a supply of cold water protected against backflow by what?
• What is the maximum travel distance allowed for a public drinking fountain from the most remote location within a tenant space?
• What type of valves necessitates the installation of a water hammer arrester?
• What is the minimum height requirement for waterproof material on shower walls and built-in tubs?
• What status does a permit hold if it authorizes the violation of plumbing code provisions?
• What is an offset in plumbing?
• What do we call the parts of a plumbing system installed before fixtures?
• What function does a faucet serve in a plumbing system?
• What is the role of a backflow prevention assembly?
• What type of water must be delivered from lavatories and group wash fixtures in public toilet facilities?
• What is the minimum drain diameter required for domestic food waste disposals?
• How should the waste pipe of a dishwasher attach to the kitchen sink system?
• What must the discharge piping have when it is installed with insert fittings?
• What must be in place before a rough-in inspection can be performed?
• How far must urinal partitions extend from the wall surface at each side of the urinal?
• In cases where different sections of the plumbing code specify varying materials or methods, which of the following provisions takes precedence?
• What shall the drainage and vent system be tested with if not using water?
• Minor plumbing repairs can be executed in the same manner as the existing system under what condition?
• When a standard's provisions overlap with those of the plumbing code, which should take precedence?
• What is the minimum size of a condensate drainage line pipe for refrigeration units between 20 and 35 tons?
• In case of practical difficulties enforcing the plumbing code, what authority does the code official have?
• Where should the discharge piping serving a temperature and pressure relief valve of a water heater terminate?
• Which device is essential for controlling water flow from the pipe system?
• What can be said about the installation requirements for water service pipes?
• Where should drinking fountains, water coolers, and water dispensers not be installed in public places?
• What is the purpose of a cleanout in the drainage system?
• What is the term for water at a temperature greater than or equal to 110°F?
• Which term refers to access enabling a fixture or appliance to be reached without removing any obstructions?
• Which code compliance is a plumbing system required to meet for installation?
• What is the minimum thickness of plastic sheathing required between copper piping and concrete?
• What does a permanent equipment permit typically require?
• What is a permit status if it does not comply with plumbing code provisions?
• Where must the required lavatory be located in relation to a water closet in employee and public toilet rooms?
• What is the maximum weighted average lead content allowed for fixtures supplying water for drinking or cooking?
• What type of inspection must occur after trenches are excavated?
• What does a backflow preventer do?
• What is classified as a branch in plumbing terms?
• What type of tank is designed specifically for flushing in plumbing?
• What types of membranes should be installed after a rough-in inspection?
• What defines the air gap in plumbing?
• What does a plumbing system include?
• What is the purpose of an air admittance valve?
• What is the maximum horizontal spacing allowed to support copper or copper alloy pipe?
• What is the primary purpose of a plumbing system?
• For horizontal pipes, at what size should rigid support and swaying bracing be provided at changes in direction greater than 45 degrees?
• What is the minimum height that urinal partitions should extend above the finished floor surface?
• Restraints shall be provided for drain pipes at changes in direction for pipe sizes greater than what size?
• When should underground inspections be conducted?
• What should trenching installed parallel to footings and walls not extend into?
• What is the purpose of a trap in a plumbing system?
• Which term describes a plumbing component that must be emptied by mechanical means?
• The discharge piping from a temperature and pressure relief valve shall not terminate more than ____ inches above the floor.
• Which of the following refers to the system that disposes of waste from plumbing fixtures?
• What type of fitting can a residential dishwasher connect to via its waste connection?
• What is the required water design capacity of bathtub mixing valves in gallons per minute?
• What device is designed to separate and retain undesirable matter from normal waste?
• What plumbing term is used to describe the system installed before final fixtures?
• If a construction method conflicts with the plumbing code, which group has the authority to assess the situation?
• What is required for buried piping throughout its entire length?
• Why are lead-free solders recommended for copper water supply piping?
• What is the function of an area drain?
• What is a common plumbing code requirement regarding water supply connections for water heaters?
• In assembly and educational occupancies, what is the maximum percentage of urinals that may substitute for required water closets?
• What do drainage fixture units represent?
• What is the significance of using lead-free solders in plumbing?
• What is a vertical vent pipe primarily used for air circulation in the drainage system called?
• How many lavatories must a restaurant have for every 200 persons served?
• What is the fitting or device that provides a liquid seal to prevent sewer gas emission?
• What is the primary consideration when installing plumbing fixtures?
• What is the primary consideration for public drinking fountain location within a tenant space?
• What is a common characteristic of hot water distribution pipes?
• Which type of assembly requires annual inspections to ensure operability?
• What is the primary function of full-open valves on water supply pipes?
• At what pressure should hot water distribution pipe and tubing be rated at a temperature of 180°F?
• What piece of equipment provides a seal to avoid air and gas emissions in plumbing systems?
• What is an on-site non-potable water reuse system?
• What is the defining characteristic of a horizontal pipe?
• What agency must label plumbing products to ensure compliance with safety and quality standards?
• In non-restaurant occupancies, how much of the required drinking fountains can be replaced by water dispensers?
• Existing metallic water service piping used for electrical grounding cannot be replaced with what until other means of grounding are provided?
• Which of the following types of toilets can be permitted when providing separate facilities for each sex?
• What is a building drain?
• What is a method for testing plumbing system piping?
• What is an Individual sewage disposal system?
• Rigid support shall be provided at changes in direction for horizontal pipes of what sizes?
• During a drainage and vent water test, how long should the water be kept in the system?
• What is a type of backflow preventer that admits atmospheric pressure through ports?
• What connects multiple drainage fixtures to a common waste and vent pipe?
• In which type of occupancy are toilet facilities required for employees?
• What is the maximum flow rate of a water closet in gallons per flushing cycle?
• What is the minimum required water pressure for testing completed sections of a water supply system?
• What type of trap is specifically designed to prevent sewer gas without affecting sewage flow?
• What is an emergency floor drain designed to protect against?
• How many extensions can a code official grant on an application for a permit?
• What is the minimum diameter for water service pipe?
• What is the minimum depth for exterior water supply system piping below the frost line?
• What does the term "main" refer to in plumbing?
• How do you calculate the required plumbing fixtures for a building based on occupant load by sex?
• How is the developed length of a pipeline defined?
• What involves the unobstructed vertical distance to the flood level rim?
• The pressure during an air test must be held for at least how many minutes?
• Public toilet facilities are not required for transactions having a public access area less than or equal to what size?
• What is necessary for plumbing products and materials to comply with referenced standards?
• Which statement is true about the installation of water service piping?
• A pan for a water heater shall not be less than ____ inches in depth.
• During which part of the construction process does a rough-in inspection take place?
• For how many days is a permit for temporary equipment and uses allowed?
• What type of joints are prohibited for cement or concrete in water service piping?
• What is a tank or pit that receives sewage or waste located below normal gravity system grade known as?